Tiansu (Tianjin) Valve Group Co., Ltd. is one of the leading manufacturers and suppliers of y strainer in China. If you're going to buy wholesale customized y strainer made in China, welcome to get quotation from our factory. Quality products and reasonable price are available.

Fluid enters the y type strainer housing through the inlet and flows along the Y-shaped passage towards the screen. Due to the design, the medium must pass through the screen to reach the downstream pipeline. The screen mesh allows only fluid to pass, intercepting solid particles and impurities on the inner side (forming a "filter cake"). Intercepted debris settles by gravity at the housing bottom (lowest point of the Y-passage), preventing screen clogging. When the pressure differential across the screen reaches a preset value (typically 0.05-0.1 MPa) or during scheduled maintenance, open the blowdown valve to discharge accumulated debris with some medium. If severe clogging occurs, close the upstream/downstream isolation valves, dismantle the end cover (or remove the screen assembly), clean the screen, and reassemble to restore function. This process is applicable to various sizes, including a large 10 inch y strainer used in main pipelines. The Y-shaped design minimizes flow resistance (compared to basket strainers) and allows natural debris settling for more thorough blowdown. Compact size allows horizontal or vertical installation (blowdown port down for vertical; down or sideways for horizontal).

Technical Parameters

Nominal Diameter: DN50-DN300(This range accommodates various industrial needs, including the use of an 8 inch y strainer)
Nominal Pressure: PN10, PN16, PN25
Operating Temperature: 0～80℃
Applicable Medium: Water

Working Principle

The y type strainer is an indispensable filtering device in fluid transport pipeline systems.

It features an advanced design, low resistance, and convenient blowdown.

It is typically installed at the inlet of pressure reducing valves, relief valves, shut-off valves (e.g., on heating system inlets), or other equipment to remove impurities and protect valves/equipment. This protection is crucial for systems utilizing large-diameter filters like an 8 inch y strainer.

Main components include connections, body, screen, flanges, end cover, and fasteners. Liquid entering the body flows into the basket, where solids are trapped, and clean fluid exits. The cylindrical basket design increases strength. The end cover at the Y-junction can be unscrewed to periodically remove accumulated debris.

Product Application

The y type strainer is a core pre-filter in industrial pipeline systems, named for its internal "Y"-shaped flow path. It primarily intercepts solid particles and impurities (e.g., sand, welding slag, rust) to protect downstream valves, pumps, instruments, etc., from wear, jamming, or clogging. Widely used in various fluid transport systems (water, oil, gas), it serves as the "first line of defense" for safe and stable pipeline operation. Its application scales from standard lines to those requiring high flow capacity, such as those employing a 10 inch y strainer.

Maintenance, Installation, and Operating Precautions

I. Daily Inspection (Daily/Weekly, Adjust Based on Conditions)

Visual & Leak Check

Observe housing, connections, blowdown valve for leaks, corrosion, deformation.

Pressure Drop & Flow Monitoring

Record pressure differential across screen. Schedule blowdown if approaching 0.05 MPa. For larger units like a 10 inch y strainer, monitoring pressure drop is key to preventing significant flow restriction.

Blowdown Valve Check

Operate blowdown valve 1-2 times to ensure smooth, non-sticking operation.

II. Periodic Maintenance (Monthly/Quarterly/Annually, Based on Service Intensity)

Maintenance Cycle	Maintenance Content	Key Points
Monthly	Screen Cleaning (Online): Open blowdown valve, backflush screen with medium (for low-debris conditions).	Backflush for 1-2 minutes with valve open. Ensure surface debris is flushed. Close valve and check if pressure drop recovers.
Quarterly	Screen Removal & Cleaning (Offline): Close isolation valves, drain housing, remove end cover/piping to extract screen.	1. Clean screen with high-pressure water or suitable solvent (e.g., diesel for oil). 2. Check screen for damage, deformation, clogging. Replace with same spec if damaged. 3. Clean housing interior, remove settled debris.
Semi-Annually	Seal Maintenance: Inspect seals (gaskets/O-rings) at end cover and connections for aging, damage, corrosion.	Replace seals with same material/spec if hardened, cracked, or leaking. Ensure sealing surfaces are clean during installation.
Annually	Comprehensive Inspection: Check housing wall thickness (especially under corrosion), wear on threads/flange faces, blowdown valve maintenance.	1. Replace strainer if wall thickness is below standard (e.g., ≥1mm wear for carbon steel). 2. Polish rusty threads/flange faces; replace connection parts if severely worn. 3. Dismantle blowdown valve, clean internal debris, inspect valve seal performance.

III. Basic Operating Requirements

A. Blowdown Operation Standard

Scheduled Blowdown

Weekly 1-2 times for normal conditions; daily for high-debris conditions (e.g., municipal wastewater, mining effluent); increase frequency for viscous media (e.g., heavy oil). The blowdown volume for a large 10 inch y strainer will naturally be greater.

Blowdown Steps

a. Slowly open blowdown valve (to avoid pipe vibration from medium surge).

b. Keep valve open 30 sec - 1 min (adjust based on debris), until discharged medium shows no significant solids.

c. Slowly close blowdown valve (avoid sudden operation).

Pressure-Drop Triggered Blowdown

When pressure drop exceeds 0.05-0.1 MPa (observed via gauges), perform blowdown or screen cleaning immediately, regardless of schedule, to prevent flow reduction, increased energy consumption, or screen rupture.

Monitor Flow/Pressure

Sudden flow drop or pressure rise likely indicates screen clogging; address promptly.

Corrosion/High-Temp Monitoring

Weekly check for housing corrosion/leaks. For high temps, confirm seals are not aged/deformed.

B. Normal Operation Monitoring

Common Faults and Solutions

Common Fault

Causes

Solutions

Screen Clogging (High ΔP)

1. Excessive impurities, untimely blowdown.

2. Screen mesh too fine.

3. Fibrous debris tangling on screen.

1. Clean screen offline; consider coarser mesh screen if downstream requirements allow.

2. Install a coarse pre-filter or fiber filter.

Connection/End Cover Leakage

1. Aged/damaged seals.

2. Threads/flanges not tightened or sealing surface dirty.

3. Worn sealing surface.

1. Replace seals, clean sealing surfaces.

2. Tighten bolts in diagonal cross pattern (re-wrap sealant on threads).

3. Polish/repair sealing surface; replace part if severely worn.

Screen Damage (Failure to intercept)

1. Incorrect screen material (e.g., standard SS for high pressure).

2. Damaged during installation/cleaning.

3. Overpressure operation causing rupture.

1. Replace with screen suitable for conditions (e.g., thickened SS for high pressure).

2. Handle screen carefully during cleaning/installation.

3. Check system pressure; ensure it does not exceed strainer rating, especially for larger models like an 8 inch y strainer.

Blowdown Valve Sticking

1. Debris entering valve core.

2. Aged seals adhering.

3. Corrosion from lack of operation.

1. Dismantle valve, clean core debris.

2. Replace seals.

3. Apply compatible anti-rust lubricant; operate valve periodically.

Hot Tags: y strainer, China y strainer manufacturers, suppliers, factory, 2 inch dynamic balance valve, 8 inch dynamic balance valve, anti water hammer silent check valve, dynamic valve, electric dynamic balance valve, rubber flap type check valve

Y Strainer