Tiansu (Tianjin) Valve Group Co., Ltd. is one of the leading manufacturers and suppliers of grooved signal gate valve in China. If you're going to buy wholesale customized grooved signal gate valve made in China, welcome to get quotation from our factory. Quality products and reasonable price are available.
A signal gate valve adds an electrical signaling function to a standard grooved gate valve. Its primary functions are to start/stop fluid flow and transmit the open/closed status. The stem drives the gate up or down to open or close the flow path. A signal device (e.g., micro switch) is activated at the full-open or full-close positions, sending an electrical signal for remote monitoring. This makes a signal grooved type gate valve a critical component for automated system oversight.
Product Core Parameters
- Nominal Diameter: DN50-DN300
- Nominal Pressure: PN10, PN16, PN25
- Operating Temperature: 0～80°C
- Applicable Medium: Water
Product Application
Signal gate valve is extensively used in fire protection systems, building water supply/drainage, and industrial pipelines. It is particularly specified for main lines in automatic sprinkler systems to isolate flow and provide electrical monitoring of that isolation status.
Maintenance & Installation Notes
Grooved type signal gate valve uses a grooved connection (couplings, gaskets) for tight linkage to pipes without welding or threading, enabling quick installation. Maintenance does not require full pipeline disassembly. Regularly check seal integrity, operational smoothness, and fastener tightness. Clean and lubricate relevant parts promptly.
Common Failures & Solutions
|
Common Failure |
Causes |
Remedies |
|
Sealing Leakage |
1. Internal leak (medium seepage when closed); 2. Stem seal leak (seepage around stem root). |
1. Flush or disassemble to clean debris; polish or replace gate if sealing surface worn; ensure full closure; 2. Tighten gland bolts; replace O-rings; polish/replace damaged stem. |
|
Operation Stiffness |
1. High operating torque (hard to turn handwheel, actuator overload); 2. Unable to hold position (handwheel spins freely, actuator travel fault). |
1. Apply temperature/water-resistant grease; loosen jammed parts and clear debris; relieve pipe stress; replace bent/worn stem/nut; 2. Replace stem nut or thrust bearing; adjust/replace limit switch. |
|
Signal Transmission Fault |
No signal at full open/close, or remote display mismatches actual status.. |
Tighten wiring terminals and check circuits; calibrate switch trigger point; replace signal switch with same model/voltage rating; calibrate stem travel and limits. |
|
Grooved Connection Leak |
Leakage at coupling joint between valve and pipe. |
Replace gasket and install flatly; evenly tighten coupling bolts with torque wrench; deburr groove; align pipe ends before tightening. |
|
Other Failures |
1. Body crack, major leak; 2. Body surface rust, coating peeled, internal rust. |
1. Stop use immediately; replace body with same spec/material; check if pipeline pressure/temperature exceeds valve rating; 2. Remove rust, paint with suitable primer/topcoat; professionally repair or replace if internal coating fails; select corrosion-resistant material/protection. |
FAQ
Q: What is the main purpose of the signaling function in a signal gate valve?
A: Its primary purpose is to provide a remote electrical indication (typically a dry contact closure) of the valve's status (fully open or fully closed), enabling central monitoring, alarm integration, and verification of system readiness in critical applications like fire suppression.
Q: How does the signal mechanism in a signal grooved type gate valve typically work?
A: A mechanical actuator (e.g., cam) is connected to the valve stem or gate. As the signal grooved type gate valve reaches its end positions, this actuator triggers a micro-switch, which changes the state of an electrical circuit that can be read by a control panel or building management system.
Q: During a pressure test, should the grooved type signal gate valve be open or closed?
A: For testing the pipeline, the grooved type signal gate valve should typically be fully open to allow water to fill the entire system and to avoid subjecting the gate to uneven pressure. However, the valve's own sealing integrity test (seat test) requires it to be closed with pressure applied from one side.
Hot Tags: grooved signal gate valve, China grooved signal gate valve manufacturers, suppliers, factory, gate valve for fire fighting system, rising stem grooved gate valve, Resilient Seat Gate Valve, non rising stem stainless steel gate valve, gate valve rising stem, gate valve fire protection
